390_22002_2
Topthema: Sound im Audi
Audio System RFIT Audi A6 C8 Evo2 – 20er System für Audi A6
Von Audio System gibt es eine Vielzahl an Nachrüstlautsprechern für Audi. Wir schaffen den Überblick und testen das RFIT Set für den A6 C8.
>> Mehr erfahren>> Alle anzeigen
462_22882_2
Topthema: Feurig
High-End-Standbox mit ESS AMT
Mit diesen Chassis wollte ich schon immer mal etwas bauen. Dass ich sie allerdings jemals zusammen in einer Box haben würde, hätte ich dann doch wieder nicht erwartet – dass das Ganze so gut werden würde, dann schon eher.
>> Mehr erfahren>> Alle anzeigenKategorie: Profi- / Musiker-Equipment
Ausstattungsliste: Manley ELOP+
Ausstattung & technische Daten
| Features | |
| STEREO LIMITER COMPRESSOR | |
| 10:1 Limiter and 3:1 Compressor ratios | |
| All-tube audio path uses 5751 and 6922 dual triodes | |
| Balanced Manley IRON® transformer-coupled XLR Inputs | |
| XLR impedance-balanced outputs | |
| BYPASS switches and AUTOMUTE with warm-up delay | |
| Large illuminated VU meters read Gain Reduction or Output levels | |
| STEREO LINK | |
| Side-Chain High-Pass Filter | |
| Universal internal power supply operates worldwide 90-250V~AC 50/60Hz | |
| Standby Power Consumption: 0.5 Watts | |
| ALL-TUBE audio path using a 5751 for gain, 6922 White Follower output tube (one each per channel) | |
| Silent Conductive Plastic GAIN control. | |
| Balanced MANLEY IRON Transformer coupled XLR input. | |
| Hi-current White Follower Impedance Balanced XLR output. | |
| Attack times are faster with higher input levels and heavier gain reduction. Typically for complete release, release times increases up to a couple of seconds, depending upon the amount of previous reduction. | |
| Specification | |
| Input impedance | 14 kOhms |
| Maximum input level | +18dBu or 4.8V RMS @ 0.01% THD |
| Output impedance | 150 Ohms |
| Maximum Output with 100 kOhm load | +30dBu @.009%THD+N, BW 22Hz-22Khz, 1Khz sine |
| Maximum Output with 600 Ohm load | +20dBu @.015%THD+N, BW 22Hz-22Khz, 1Khz sine |
| Output Headroom (Referenced to +4dBu) | 26dB |
| Frequency Response | -0.15dB @ 10Hz, -0.1dB @ 20KHz |
| Total Harmonic Distortion (1kHz sine @ +4dBu, BW 22Hz-22kHz) | 0.004 % THD+N |
| Noise Floor Limiter Bypass | -90dBu (BW 22Hz-22kHz) |
| Noise Floor Limiter Engaged | 88dBu (BW 22Hz-22kHz) Input set to Unity gain |
| Dynamic Range | 118dB |
| Signal to Noise Ratio | 92dB (Referenced to +4dBu) Bypass mode = Signal goes thru ALL-TUBE audio path (Bypa |
| Unity Gain | Set Input Attenuator @ 1:00 o clock |
| Maximum Gain | 13 dB |
| Common-Mode Rejection Ratio (CMRR) | 77dB (BW 22Hz-22Khz, +4dBu, 1Khz sine) |
| Limiter Ratio | 10:1 |
| Compressor Ratio | 3:1 |
| Limiter: Attack | 15ms |
| Limiter Release | 200ms |
| Compressor: Attack | 75ms Release= 200ms |
| Attack/Release times measured under following conditions | 4dB of Gain Reduction, 1kHz sine, +4dbu Input level, to 63% of total. |
| Maximum Limiting (with +4dBu 1Khz sine) | 12dB |
| Maximum Compression (with +4dBu 1Khz sine) | 6dB |
| Side-Chain High Pass Filter | 80Hz (Internal user adjust jumper to 150Hz) |
| Automute warmup delay | 30 seconds |
| Operating mains voltage | 90 to 254 VAC (internal universal power supply) |
| Mains voltage Frequency | 50-60 Hz |
| Power consumption | 26 Watts |
| Dimensions= (w,d,h) | 19" x 7 x 3 1⁄2" (occupies 2u) |
| Unit weight | 9.5 Ib |
