Mit diesen Chassis wollte ich schon immer mal etwas bauen. Dass ich sie allerdings jemals zusammen in einer Box haben würde, hätte ich dann doch wieder nicht erwartet – dass das Ganze so gut werden würde, dann schon eher.
>> Mehr erfahren>> Alle anzeigenEs gibt Lautsprecher und dann gibt es noch die LS3/5A. Sie spaltet sowohl ihre Hörer, als auch die, die sie gar nicht kennen. Warum das so ist? Nun, dafür muss man sich vor allem anschauen und natürlich hören, was sie kann und nicht, was sie nicht kann.
>> Mehr erfahren>> Alle anzeigenKategorie: Lautsprecher Inwall
Ausstattungsliste: Tannoy CMS 801DC
Specification | |
SYSTEM | |
Frequency Response (-3dB) (1) BM Back can | 47Hz - 30kHz |
Frequency Range (-10dB) (1) BM Back can | 40Hz - 35kHz |
Frequency Range (-10dB) (1) PI Back can | 41Hz - 35kHz |
System Sensitivity (1W @1m) (2) | 92dB (1W = 2.83V for 8 Ohms) |
Nominal Coverage Angle | 90 degrees conical |
Coverage Angle (1kHz to 6kHz) | 100 degrees |
Directivity Factor (Q) | 5.5 averaged 1kHz to 6kHz |
Directivity Index (DI) | 7.2 averaged 1kHz to 6kHz |
Rated Maximum SPL | Average: 112dB Peak: 118dB Average: 110dB (with THP60) |
Power Handling (3) | Average: 90W Programme: 180W Peak: 360W |
Recommended Amplifier Power | 180W @ 8 Ohms |
Nominal Impedance | 8 Ohms |
Transformer Taps (via front rotary switch) | 70V: 60W / 30W / 15W / 7.5W / OFF & Low Impedance operation 100V: 60W / 30W / 15W / OFF & Low Impedance operation |
Crossover | 2kHz - 2nd order LF, 2nd order HF (with dynamic HF protection) |
TRANSDUCERS | |
Low Frequency | 1 x 200mm (8.00") Dual Concentric™ constant directivity driver with multi fibre paper pulp cone |
High Frequency | 1 x 25mm (1.00") titanium dome with neodymium magnet system |
PHYSICAL | |
Enclosure | Back Can: Zinc plated steel Baffle: Reflex loaded UL 94V-0 rated ABS Grille: Steel, with weather resistant coating |
Safety Features | Safety ring located at rear of enclosure for load bearing safety bond |
Clamping Design | Min / Max clamping range: 0.0mm (0.0") / 20.0mm (0.79") Recommended clamp torque: 1.5Nm |
Back Can Options | Blind Mount (BM): Complete with fixed back can Pre Install (PI): Separate back can for pre installation |
Cable Entry Options | Cable clamp & squeeze connector for conduit up to 22mm |
Conduit Knockouts | 3 Sets of horizontal positions: 19 / 22 / 28mm 0.75 / 0.87 / 1.10" |
Connectors | Removable locking connector with screw terminals with "loop through" facility |
Safety Agency Ratings | CE, UL-1480, UL-2043 |
BM Hole Cutout Diameter | 295mm (11.61") |
PI Hole Cutout Diameter | 295mm (11.61") |
Dimensions | Bezel diameter: 325mm (12.80") BM model: Front of ceiling to rear of back can 310.50mm (12.22") BM model: Front of ceiling to top of safety loop 327.80mm (12.90") |
PI model: Front of ceiling surface to rear of speaker unit 118.70mm (4.67") PI model: Front of accessory back can bezel to top of safety loop 168.50mm (6.63") | |
Net Weight (ea) | CMS801 DC BM: 6.5kg (14.33lbs) CMS801 DC PI: 2.5kg (5.51lbs) CMS801 Plaster (Mud) Ring: 0.3685kg (0.81lbs) CMS801 PI 8 Ohm back can: 4kg (8.81lbs) CMS801 DC 60W transformer kit 8 Ohm : 1.095kg (2.41lbs) |
Included Accessories | C Ring Tile bridge Paint mask Cutout template Grille |
Optional Accessories | Plaster (mud) ring |
305-2128
MD Sound GmbH & Co. KG |